进口水用电磁阀 德国洛克水用电磁阀

一、进口水用电磁阀产品概述：

德国《LOCKE》洛克--进口水用电磁阀适用于以水或液体为工作介质，可自动化控制或远程控制水、油、液体等工作介质管路的通断。由于本阀 采用橡胶密封，故对工作介质的清洁度大大减低，进口水用电磁阀具有起笔迅速，可靠性能高等特点。

1、 Overview of imported water solenoid valve products:

Locke imported water solenoid valve is suitable for automatic control or remote control of water, oil, liquid and other working medium pipelines with water or liquid as working medium. Because the valve is sealed with rubber, the cleanliness of the working medium is greatly reduced. The imported water solenoid valve has the characteristics of quick start and high reliability.

二、进口水用电磁阀技术参数：

流体温度：-5≤80℃

环境温度：-5≤55℃

标称路径：DN 15-300

工作压力：1.0Mpa~1.6Mpa

连接方式：内螺纹法兰

控制模式：正常关闭，正常打开

阀体材料：黄铜(DN15-50)、不锈钢(DN15-50)、铸铁(DN40-300)

标准电压：AC220V，DC24V(其他特殊)

电气连接：接线盒式(3个端子)

功率消耗(VA)：DN15-50，17 VA;DN65-300，50VA

保护等级：标准IP 54，塑料密封IP 65(DN 15~DN 50)

流体范围：水、空气、粘度≤4°E油及其他非腐蚀性液体、气体

特殊功能：e防爆;S手动功能;X信号反馈;T定时开关;K常数开启功能。

2、 Technical parameters of imported water solenoid valve:

Fluid temperature: - 5 ≤ 80 ℃

Ambient temperature: - 5 ≤ 55 ℃

Nominal path: DN 15-300

Working pressure: 1.0MPa ~ 1.6Mpa

Connection mode: internal thread flange

Control mode: normal off, normal on

Valve body material: brass (DN 15-50), stainless steel (DN 15-50), cast iron (DN 40-300)

Standard voltage: AC220 V, DC24 V (other special)

Electrical connection: junction box type (3 terminals)

Power consumption (VA): DN 15-50, 17 VA; DN65-300，50VA

Protection class: standard IP 54, plastic seal IP 65 (DN 15 ~ DN 50)

Fluid range: water, air, viscosity ≤ 4 ° E oil and other non corrosive liquids and gases

Special function: e explosion proof; S manual function; X signal feedback; T timing switch; K constant on function.

三、进口水用电磁阀性能特点：

是用电磁控制的工业设备，是用来控制流体的自动化基础元件，属于执行器，并不限于液压、气动。用在工业控制系统中调整介质的方向、流量、速度和其他的参数。电磁阀可以配合不同的电路来实现预期的控制，而控制的精度和灵活性都能够保证。

3、 Performance characteristics of imported water solenoid valve:

It is an industrial equipment controlled by electromagnetism and an automatic basic component used to control fluid. It belongs to actuator and is not limited to hydraulic and pneumatic. It is used to adjust the direction, flow, speed and other parameters of the medium in the industrial control system. The solenoid valve can cooperate with different circuits to achieve the desired control, and the control accuracy and flexibility can be guaranteed.

四、进口水用电磁阀工作原理：

有密闭的腔，在不同位置开有通孔，每个孔连接不同的油管，腔中间是活塞，两面是两块电磁铁，哪面的磁铁线圈通电阀体就会被吸引到哪边，通过控制阀体的移动来开启或关闭不同的排油孔，而进油孔是常开的，液压油就会进入不同的排油管，然后通过油的压力来推动油缸的活塞，活塞又带动活塞杆，活塞杆带动机械装置。这样通过控制电磁铁的电流通断就控制了机械运动。

4、 Working principle of solenoid valve for inlet water:

Each hole is connected with a different oil pipe. There are two electromagnets on both sides of the cavity and a piston in the middle of the cavity. The valve body will be attracted to which side when the magnet coil is energized. Different oil drain holes can be opened or closed by controlling the movement of the valve body. The oil inlet hole is normally open, and the hydraulic oil will enter into different oil drain pipes, Then through the oil pressure to push the piston of the cylinder, the piston drives the piston rod, and the piston rod drives the mechanism. In this way, the mechanical movement is controlled by controlling the current on and off of the electromagnet.