进口低温电磁阀 德国洛克 型号齐全 总有一款让你心动

 进口低温电磁阀 德国洛克 型号齐全 总有一款让你心动

关于德国《LOCKE》洛克

德国LOCKE洛克国际集团有限公司成立于1875年，是一家流体制造商，主要服务于全球工业、以石油，天燃气，石化、蒸汽、水系统以及各类型流体控制系统，公司致力于产品设计、研发、制造、销售，为用户提供完善的流体控制方案和阀门制定方案。目前LOCKE在德国本土拥有3家阀门生产工厂，分别位于总部弗兰肯塔尔，佩格尼兹和侣能三地，并在中国设立全资加工厂，主要负责亚洲地区产品供应，在上海设立销售代理处，负责大陆运营及售后服务。

进口低温电磁阀产品概述：

德国《LOCKE》洛克--进口低温电磁阀（Temperature solenoid valve ）是指用于温度在-40℃至-196℃低温介质的管道系统，如液化天燃气，液化氧气，液化氮气，LNG，低温介质的电磁阀。

进口低温电磁阀产品特点：

进口低温电磁阀具有,寿命长：此阀结构简单，故障少，维修方便，阀芯由特种不锈钢制成，耐磨性好，耐超低温。本产品采用不锈钢阀芯，在长时间不动作情况下启动阀门，动作迅速，快速切断；线圈长时间通电，发热量低，不会烧毁，功耗底，节能；零压启动，零泄漏。

进口低温电磁阀工作原理：

常闭：当线圈通电时，先导阀芯吸合，先导孔打开，阀上腔卸压，活塞靠下腔介质压力推动，电磁阀打开。
当线圈断电时，先导阀芯靠弹簧复位，先导孔关闭，阀上腔由活塞节流孔增压和复位弹簧的推力，电磁阀关闭。
常开：当线圈通电时，先导阀芯靠弹簧复位，先导孔关闭，阀上腔由活塞节流孔增压和复位弹簧的推力，电磁阀关闭。
当线圈断电时，先导阀芯靠弹簧复位，先导孔打开，阀上腔卸压，活塞靠下腔介质压力推动，电磁阀打开。
注：出口端压力大于进口端压力，介质会反向导通。可安装止回阀。

Normally closed: when the coil is energized, the pilot valve core is closed, the pilot hole is opened, the pressure in the upper chamber of the valve is relieved, the piston is pushed by the medium pressure in the lower chamber, and the solenoid valve is opened.

When the coil is powered off, the pilot valve core is reset by the spring, the pilot hole is closed, the upper chamber of the valve is pressurized by the piston orifice and the thrust of the reset spring, and the solenoid valve is closed.

Normally open: when the coil is energized, the pilot valve core is reset by the spring, the pilot hole is closed, the upper chamber of the valve is pressurized by the piston orifice and the thrust of the reset spring, and the solenoid valve is closed.

When the coil is powered off, the pilot valve core is reset by the spring, the pilot hole is opened, the pressure in the upper chamber of the valve is relieved, the piston is pushed by the medium pressure in the lower chamber, and the solenoid valve is opened.

Note: if the outlet pressure is greater than the inlet pressure, the medium will conduct reversely. Check valves can be installed.

进口低温电磁阀性能范围：

进口低温电磁阀特别提示：

1、电磁阀如出口压力大于进口压力，阀将反向导通，此时应安装止回阀。
2、介质中有杂质，请安装过滤网30-100目/寸。
3、电磁阀水平安装，即线圈在上较佳，如需垂直安装，特别提出。
4、公司专门为你设计特殊需要的产品。