青海低密度风电叶片修补胶，风力发电扇叶缺陷修补找平专用环氧树脂腻子 新价格

青海低密度风电叶片修补胶产品密度低，强度高。风力发电扇叶缺陷修补找平专用环氧树脂腻子 新价格 

青海低密度风电叶片修补胶由高性能的环氧树脂和优质的填料、助剂、固化剂精心配制而成。该产品具有良好的绝缘性，较高触变性，非常好的操作性，能够很容易的刮涂在电气产品的表面，进而达到填平、修补、防水防潮的目的。

风力发电扇叶缺陷修补找平专用环氧树脂腻子生产商微信

青海低密度风电叶片修补胶密度低、自身重量轻，修补强度高是风电叶片修补、贴布修补找平的 产品。

一、1、 凡需要修补找平、防水防潮的各类电气产品均可使用；
2、 广泛应用于户外干式互感器、变压器、电抗器等电气的修补找平，对于金属、陶瓷、树脂固化物之间的粘接修补，有优异的电气性能和防水性能；
3、对于有弹性或软质外壳类产品的粘接修补会根据实际情况做出调整。
三、产品相关性能指标

机械性能

电气性能

青海低密度风电叶片修补胶的修补方案

   1、 清洁：要修补的叶片必须充分干燥，做打磨处理，并把表面的灰尘、粉状颗粒物及其他脏物处理干净。

   2、 施工：将电力环氧修补腻子的AB料按照1：1的重量比分别称好后，在主剂A料中加入固化剂B料，用电钻搅拌5-10分钟，使固化剂B与主剂A完全混合均匀（色泽一致），取AB混合后的腻子刮于电气需要修补的界面上。室温下12小时即可固化，48小时后达到 性能。

青海低密度风电叶片修补胶使用注意事项：

.操作现场和工作环境必须保持空气流通，防止空气中化工液体挥发后浓度过高，引起工作人员身体不适（呼吸道和皮肤刺激等）。

.使用中请勿用手揉擦眼睛，并采用适当的防护措施。

.如果胶液溅入眼睛，请立刻用大量清水冲洗，并请就医处理。

.如果胶液接触到皮肤，请立即用 酒精擦拭干净，并用肥皂和清水冲洗。

1 Introduction:

This product is solvent-free epoxy putty from the metal pail of A, B component composition, A component epoxy resin, toughening agents, coupling agents, leveling agents, defoamers, anti-settling agents made, B component by a high-temperature curing agent, anti-rust paint, etc. made by the construction of A: B = 1:1 mixed before use.

Epoxy putty filler made of high quality resin and purification, 100 solids, solvent and other volatile harmful substances. At room temperature after mixing the epoxy putty Stir to use, without adding any additional ingredients. The product is easy to operate, non-toxic, non-irritating odor, mixed cured high temperature, strong adhesion, high hardness, weather resistance, water resistance, oil resistance and excellent performance.

2  Purposes:

This product can be used at room temperature and curing at room temperature as well. It is simple for site construction.

it has good adhesion to putty, cast iron, steel, concrete and other surfaces. After curing hard, it is dense, moisture-resistant, and good water resistance. It is good for cast iron steel, steel plate concrete surface repair, leveling and brushing to form a protective layer.

3  Product Features:

Compressive strength, bonding and other physical and mechanical properties far superior to other materials.

No shrinkage: no shrinkage after molding to ensure high accuracy brushing needs.

Corrosion resistance: can stay with acid, alkali, salt, oil and other chemicals, long-term exposure to corrosion.

Excellent creep resistance: in the -80 ° C to +100 ° C alternately freezing and thawing, vibration pressure long-term use in harsh physical conditions without plastic deformation, ensuring the long-term precision positioning equipment.

4  Physical performance range of product

Item Index value detection value test

Compressive strength (ultimate result, MPa) 70 72.7 GB/T50367-2006

Flexural strength (the final result, MPa) 50 51.0 GB/T50367-2006

Modulus of elasticity (the final result, MPa) 2.5 × 103 2.9 × 103 GB/T50367-2006

Thermal expansion coefficient (final result) <40 × 10-6mm/mm / ° C GBJ119-88

Linear Shrinkage (final result) ----- HG/T2625-94

5 Ratio: epoxy putty A: epoxy putty B = 1:1

Packing: 25KG / drum

The product is in accordance with the general chemical transport.

Note: The above data for reference only, please be sure to experiment before using the relevant properties.