恒创利 SM-10双面机 SM-E双面机

7、SM-F type double facer双面机    

ⅰ、Structural features结构特点：

★The surface of the heating plate is grinded, the width of the hot plate is 600mm, there are 16 heating plates, the cooling setting is 4 meters.The heating plate is made of vessel plate, which conforms to the national first-class pressure vessel standard, with pressure vessel certificate and inspection certificate.

加热板表面经研磨处理，热板宽度600mm，共16块加热板，冷却定型部长4米。加热板采用容器板制作，符合国家一类压力容器标准，附有压力容器证书及检验合格证。

★The upper conveyer belt rectifies the right and left side to adopt the pneumatic automatic correction deviation.

上输送带左右纠偏调整采用气动自动纠偏。

★Heating plate heat transfer pipe temperature control sub-four-segment, with a temperature display.  加热板的导热配管分四段控制温度，设有温度显示。

★Double cylinder S type cotton belt tensioning device is used for upper cotton belt.

上棉织带采用双气缸S型棉织带张紧装置。

★The lower belt adopts pneumatic tension, pneumatic correction.下带采用气动张紧，气动纠偏。

★Drive roller coated with attached wear-resistant rubber ，showed a herringbone structure，With a high, ensure smooth cardboard output。

驱动辊表面包附耐磨像胶，呈人字型结构，并带有中高，保证纸板平整输出。

★Main drive motor for frequency conversion motor，low-speed torque，wide speed range ,reliable, and easy maintenance.

主驱动电机为变频调速电机，低速力矩大，调速范围广，使用可靠，维护简单。

★Hot plate internal for partition isolation structure,s-shaped flow of steam，Steam, water separation function significantly improves the utilization of steam。

热板内部为隔板隔离结构，使蒸汽呈S形流向，汽、水分离功能明显，提高了蒸汽利用率。

ⅱ、Technical parameter技术参数：

★Temperature requirement：160—200℃                  温度要求：160—200℃   

★Steam pressure：0.8-1.3MPa                           蒸汽压力：0.8-1.3MPa        

★Air source pressure：0.6—0.9MPa                      气源压力：0.6—0.9MPa 

★Cooling stereotypes length：4m                         冷却定型长度：4米      

★Heating plate quantity：16 pieces                       加热板数量：16块            

ⅲ、Roller diameter parameter辊类直径参数：

★Upper drive rubber roller diameter：￠700mm            上驱动胶辊直径：￠700mm          

★Lower drive rubber roller diameter ：￠400mm           下驱动胶辊直径：￠400mm       

★Former follower with roller diameter：￠215mm           前从动带辊直径：￠215mm          

★Back setting belt driven roller diameter：￠215mm        后定型从动带辊直径：￠215mm

★Platen roller：￠70mm                                 压带辊直径：￠70mm           

★Setting roller diameter：￠86mm                        定型托辊直径：￠86mm

★Upper belt tension roller diameter：￠155mm             上带张紧辊直径：￠155mm         

★Upper roll diameter with detuning：￠130mm             上带调偏辊直径：￠130mm

★Entrusted with the roll diameter lower belt：￠130mm      下带托带辊直径：￠130mm

★Lower belt tension roll diameter: ￠130mm                下带张紧辊直径：￠130mm  

Note: All the roller surface after grinding are hard chrome plated。

注：所有辊轴表面均为磨削后镀硬铬处理。

ⅳ、Powered motor parameters动力电机参数：

★Main drive motor power：30Kw                          主驱动电机功率：30KW