输送燃油泵 200CYZ-63柴油自吸泵 泵配90kw-4电机铜叶轮口径200流量280立方

输送燃油泵 200CYZ-63柴油自吸泵 泵配90kw-4电机铜叶轮口径200流量280立方

   我公司是一个生产齿轮油泵和螺杆泵的专业公司。公司拥有各种设备80台,主要设备有：C6140 CW6163C车床24台，TX611C/4镗床2台，M131M7130磨床8台，C125A立车2台，Y318K Y3150E滚齿机6台，E3050X16/1摇臂钻床2台，E5163立式钻床2台，B1-400 铣床3台，螺杆泵转子专用QH2-007铣床1台，半自动螺旋转子QH2-029B铣床2台，X53K立铣3台，半自动螺旋转子QH2-031 QH2-032磨刃机台。My company is a company specialized in the production of gear oil pump and screw pump.Company has 80 sets of various devices, the main equipment are: C6140 CW6163C 24 sets of lathe, TX611C/boring machine 2 units, 4 M131M7130 grinding machine 8 units, C125A set, 2 sets, Y318K Y3150E hobbing machine 6 units, E3050X16/1 radial drilling machine 2 sets, E5163 vertical drilling machine 2 sets, B1-400 universal milling machine 3 units, screw pump rotor 1 QH2-007 milling machine, semi-automatic screw rotor QH2-029 - b milling machine 2 sets, X53K three vertical milling, semi-automatic screw rotor QH2 QH2-031-031 edge grinding machine is used.

   我公司拥有省计量局制试验台1台，自制试验台3台，使生产产品从原材料投入到产成品出厂实现了全过程检测。产品出厂合格率 ，具备较强的综合配套制造能力。理化试验室、长度计量室是国家计量确认合格单位，使产品从原材料投入到产成品出厂实现了全过程检测。产品出厂合格率 ，具备较强的综合配套制造能力，公司年可生产各种泵6000多台。My company has the province system test bench 1 bureau of standard measurement, homemade test-bed 3 units, production of products from raw materials into finished goods factory implements the whole process of detection.Product factory qualified rate , have strong ability of comprehensive manufacturing.Physical and chemical laboratory, length measuring room is the national metrological confirmation unit, make our products from raw materials into finished goods factory implements the whole process of detection.Product factory qualified rate , have strong comprehensive manufacturing capacity, company can produce all kinds of pump in more than 6000 units.

运费说明:

   1.本公司常规产品1-3天发货,特殊要求或者需定做的产品发货时间已与客户协商为准, 2.泵运费方式有两种:快递和物流.小泵和小型配件发快递,其余体积较大,数量较多,推荐走专线物流货运,一般南方,中部地区及沿海地区3-5天左右到达.西部,北部较远的地区以及少数二次中转地区5-8天左右可到,具体覆盖范围请咨询公司客服人员.安装使用:请您根据产品说明书的步骤进行操作,如有问题,请联系我公司.为了保护您的利益,我们已经提醒客户在收到货物时,要开箱验货,如在打开验货时发现货物丢失,损害或者不符,请拒 签收,您签收就代表已准确无误的收到后屋,若在签收货物之后才发现货物丢失或者不符,如不负责.客户收到货后,产品无法安装或者规格有误,本公司提供退货或者换货服务,退货或者换货的客户请保证货物的完好无损,并承担往返运费.客户收到后,如果产品存在质量问题,请在收货后7天内联系我公司,提供相关质量问题图片,我公司将在 时间给您退货或者换货,因为我公司已经在发货前已经仔细检查过,所以过期将不提供此项服务,还请谅解.Shipping details:1. Our regular products 1-3 days of delivery, special requests or need to custom-made product delivery time is already negotiate with customer, 2. The pump freight way has two kinds: express and logistics. Small pump and small accessories send express, the rest of the volume is larger, the number is more, recommend special line logistics, freight, generally south, central and coastal area about 3 to 5 days to arrive. In the west, north of remote areas and areas inhabited by minority secondary transit, about five to eight days to specific coverage please consulting company customer service staff. Install and use, please according to the product manual steps, if any problem, please contact our company, we advise you that we will be the most professional and technical personnel to provide service for you. In order to protect your interests, when we have to remind the customer receive the goods, unpacking inspection, such as when open the inspection found that the goods lost, damage or discrepancy, please refuse to sign after receiving STH, you sign after receiving STH means have accurate received after the house, if after receipt of goods found the goods didn\'t agree lost or, if not responsible. Customers after receiving the goods, the product can\'t install or specification is wrong, the company provides the return or exchange service, return or exchange the customers please make sure that the goods are intact, and bear the freight back and forth. The receipt of the customer, if the product quality problems, please contact me within 7 days after receiving the company, provide relevant quality problem photos, our company will give you a refund or a replacement in the first time, because I already have carefully checked before shipment, so late will not provide this service, also please understand.

    自吸泵的自吸高度，与叶轮前密封间隙、泵的转数、分离室液面高度等因素有关。叶轮前密封间隙越小，自吸高度越大，一般取为0.3~0.5毫米；在间隙增大时，除自吸高度下降外，泵的扬程、效率均降低。泵的自吸高度随叶轮的圆周速度u2的增大而增大，但到 自吸高度时，转数增加而自吸高度就不再增加了，此时只是缩短自吸时间；当转数下降时，自吸高度则随着下降。在其它条件不变的情况下，自吸高度还随着储水高度的增加而增加（但也不能超过分离室的储水高度）。为了在自吸泵中更好地使气水混合，叶轮的叶片须少些，使叶栅的节距增大；并宜采用半开式叶轮（或叶轮槽道较宽的叶轮），这样更方便于回水深入地射进叶轮叶栅中。
自吸泵大部分与内燃机配套，装在可移动的小车上，宜于野外作业。Self-g pump self-g height, and before the impeller seal clearance, the revolutions of the pump, separation chamber level and other factors.Before the impeller seal gap is smaller, the greater the self-g height, general take 0.3 ~ 0.5 mm;Increase in clearance, in addition to the self-g height decreased, pump lift and efficiency are reduced.The self-g pump
    自吸油泵的使用及维护
    1 启动前的准备及检查事项1 to start preparing and check the item before
    1.1 检查轴承体油腔中润滑油是否已达到规定要求，润滑油的油位应保持在机油尺的两刻线之间或油标中线位置,不得过多或不足.1.1 check whether oil bearing body cavity, the lubricating oil has reached the specified requirements, the lubricating oil in the oil level should be kept in the oil foot or oil standard midline position between two scribed line, not too much or not.
    1.2 检查泵体内的储液是否高于叶轮边缘.如若不足,可以从泵体上的加液口直接向泵体内注入储液,不应在储液不足的情况下启动运转,否则泵体不能正常工作,且易损坏机械密封.1.2 check reservoir is higher than that of the impeller in the pump body. If not, can add liquid mouth from the pump body directly to the pump body into the reservoir, the defects in the reservoir should not start operation, under the condition of pump body can not work normally, and easy to damage the mechanical seal.
    1.3 检查泵转动部件是否有卡住磕碰现象.1.3 check the pump rotating components for stuck knock against.
    1.4 检查泵体底脚及各连接处有无松动现象.1.4 check the pump body foot and joint have loose phenomenon.
    1.5 检查泵轴与原动机主轴的同轴度与平衡度.1.5 check the pump shaft and prime mover of main shaft alignment and balance.
    1.6 检查进口管路是否漏气1.6 check whether import pipeline leak
    1.7 打开吸入管道的阀门(注意不要全开)1.7 open the suction piping valves (be careful not to open)

    2 启动及操作2 start-up and operation
    2.1 启动油泵,注意泵轴的转向是否正确2.1 start the oil pump, pay attention to the steering pump shaft is correct
    2.2 注意转动时有无异常噪音和振动2.2 notice there is no abnormal noise and vibration
    2.3 注意真空表读数,启动后当压力表及真空表的读数经过一段时间的波动而时针稳定后,说明泵内已经上液,油泵竟如正常工作状体.2.3 pay attention to the vacuum meter reading, starts when the pressure gauge and vacuum gauge readings over a period of time after hour due to the variation of stable, explain within the pump has been on fluid, oil pump body become like a normal job.
    2.4 在泵进入正常输油作业前,应特别注意泵内油温升高情况,如果这个过程长,泵内油温过高,则应停泵检查原因.2.4 before the pump into the normal oil operation, should pay special attention to pump the high oil temperature rise, if the process is long, inside the pump oil temperature is too high, you should stop the pump to check.
    2.5 如果泵内温度过高而引起自吸困难.可暂时停机,利用出口管路中的液体倒流或直接向泵内补充液体,使泵内液体降温,即可启动.2.5 if the high temperature caused by self pump difficult. Can temporarily stop, using the export pipeline fluid replacement in the liquid backflow or directly to the pump, cooling the liquid in the pump, can be started.
    2.6 泵在工作过程中因故停泵,需在启动时,把出口控制阀稍开.这样既有利于自吸过程中其他从吐出口排出,又能保证泵在较轻的负荷下启动.2.6 pump in the process of work for pump stopped, at startup, the export control valve slightly open. This is beneficial to both other exported from spitting out during the process of imbibition, and can guarantee the pump starts under a lighter load.
    2.7 泵每工作15-20小时或每次使用前应检查并及时补充一次10号机械油.2.7 pump every 15 to 20 hours or every time before the use should check and added a number 10 machine oil in time.
    3 停车
    3.1 关闭吐出管路上的闸阀
    3.2 使泵停止转动
    4 易损件的维护
    4.1 滚动轴承:当油泵长期运动后,油泵磨损到一定程度必须更换
    4.2 前后密封环:当密封环磨损到一定程度时,须进行更换
    4.3 机械密封:在不漏油的情况下,一般不应拆开检查,若轴承体下端泄漏口处产生严重泄露时,则应对机械密封进行拆检.装拆机械密封时,必须轻取轻放,注意配合面的清洁,不好好动、静环表面的光洁度，严禁敲击碰撞。

     自吸离心泵的过流部件    Self-g centrifugal pump flow components
     自吸离心泵的过流部件有：吸入室，叶轮，压出室三个部分。叶轮室是泵的核心，也是流部件的核心。泵通过叶轮对液体的作功，使其能量增加。叶轮按液体流出的方向分为三类： Self-g centrifugal pump flow components are: suction chamber, impeller, the pressure out of the room three parts.Room is the core of the pump impeller, and also the core of the flow components.Of liquid through the impeller pump work, allow it to increase energy.According to the direction of liquid flow impeller is divided into three categories:   
    （1）径流式叶轮（离心式叶轮）液体是沿着与轴线垂直的方向流出叶轮。    （2）斜流式叶轮（混流式叶轮）液体是沿着轴线倾斜的方向流出叶轮。    （3）轴流式叶轮液体流动的方向与轴线平行的。
     叶轮的分类
     叶轮按吸入的方式分为二类：
    （1） 单吸叶轮（即叶轮从一侧吸入液体）。    （2） 双吸叶轮（即叶轮从两侧吸入液体）。   
     叶轮按盖板形式分为三类：    （1） 封闭式叶轮。    （2） 敞开式叶轮。    （3） 半开式叶轮
     According to the classification of the impeller impeller suction way is divided into two categories:
(1) single suction impeller (i.e., from one side suction impeller liquid).(i.e., (2) double suction impeller impeller from either side suction liquid).  
Impeller press flat form is divided into three categories: (1) closed impeller.(2) open type impeller.(3) half open impeller
   ●特点: CYZ自吸泵属自吸式离心泵系列。具有结构简单、操作维护方便、运行平稳、排量大、效率高、便于调节，有较强的自吸能力，适用范围广等特点。

    ●用途： CYZ自吸泵用来输送汽油、 、柴油、航空煤油等石油产品。介质温度在-20℃～+80℃，是一种优良的船用装卸油泵，可兼作扫舱水泵。并适用于陆地油库、油罐车等储油装置的油料输送。也可以用来输送海水、淡水等。

    ●结构型式： CYZ自吸泵采用轴同回液的泵体结构，泵体由吸入室、储液室、涡旋室、回液孔、气液分离室等组成。泵的轴承采用单列向心球轴承。在一些泵的轴承体底部设有冷却室。泵内部高、低压区间有密封环。轴端采用机械密封。

1.本公司常规产品1-3天发货,特殊要求或者需定做的产品发货时间已与客户协商为准,
2.泵运费方式有两种:快递和物流.小泵和小型配件发快递,其余体积较大,数量较多,推荐走专线物流货运,一般南方,中部地区及沿海地区3-5天左右到达.西部,北部较远的地区以及少数二次中转地区5-8天左右可到,具体覆盖范围请咨询公司客服人员.
安装使用:请您根据产品说明书的步骤进行操作,如有问题,请联系我公司.

1.本公司常规产品1-3天发货,特殊要求或者需定做的产品发货时间已与客户协商为准,
2.泵运费方式有两种:快递和物流.小泵和小型配件发快递,其余体积较大,数量较多,推荐走专线物流货运,一般南方,中部地区及沿海地区3-5天左右到达.西部,北部较远的地区以及少数二次中转地区5-8天左右可到,具体覆盖范围请咨询公司客服人员.
安装使用:请您根据产品说明书的步骤进行操作,如有问题,请联系我公司.